Відео

Good diagnosis right to the point CHEERS WILL

Thanks Will!

4:21 how is this bushing removed without having a special tool similar to OTC 308-070 ? Maybe the whole rear cover must come off and then knock it out ? Will ?

👍👌🌞🇺🇸 thanks Will!

Will , in all the driveline, transmission videos ive watched, never been instructed on putting blocks on wheels when drveline being done, or putting in neutral, from park Thanks for that important information!. For us Diy'er s.👍👌☀️

Not terrible access this time. Your skills are worth watching!

Nice diag & repair Will

First 😎

Mine does the same thing. Except my speedometer and rpms drop off😂... I did a front battery delete and run an external voltage meter as most bassheads do. Your not alone bro...😢😂🎉 Its from music for sure... 150 db is a car killer

Can I drive with this issue?

This was a satisfying one! Great diagnosis and fix! Thanks for sharing.

Just found your Video researching Why my Header I ordered back in may doesn't fit. Apparently the Offending Brand new Header is for a 5.3. Mine is a 6.0, not Doughnut type gasket on passenger side... now trying to figure out what next...

Typical poor design! Having a piece of plastic taking so much strain on a threaded metal rod,what could go wrong? I opened up my tailgate and found one side like this with string wrapped around it instead of a zip tie.

Happy 4th, Will. I'd replace the carrier bearing assembly and the rear seal. I always thought those vans were cool. Too bad they were never made in 4wd and...they're Nissans. 🤣

Happy 4th of july🎉

Hello, Robinson how can I get a PCM control module need one for jeep wrangler 2005- 4.0 6cyclinder

Enjoy the holiday and be safe there.⚜

Happy 4th of July, I lived 42 years on the beautiful Country in California. I am retarded in my México. Un saludo desde Chihuahua México. I see all your 📹 🎥 you are great technician God bless America and you an family.

Excellent will, there are mechanics, and then there are great mechanics like you!👌👍🌞☀️🇺🇸

Good job!

Never give up

Great work and thank you for the video boss

Super diag & repair. Always interesting but hopefully they are not all this difficult. Time is money and here’s hoping you also get many easier jobs as well.

Tons of potential problems in that confined spot on the steering column. Persistence, once again, paid off. Nice work Will.

I see GM also with those wire rubbing issues. These This engineers and designers make the wires long enough so they won't be touching stuff things would be a better

Good work, Robinson. You sent that one out on its Edge again.

Thanks! Nice spot.

As soon as I saw the damage I was like "how is he going to get to those wires"? I'm glad they could be disconnected for access. Nice find!

Nice job, Will. That was an odd one. No parts required! 🤣

Nice repair Will, that harness won't come near that u-joint anymore!

When you can trigger the fault with movement, it's likely some mechanical problem with the wire, in this case the clock spring. Strangely it may be the communication wire, or perhaps a ground/power feed to an internal module. I'm looking forward to the full video!

sounds like clock spring

My 19 Durango ac starting to mess around now

Robinson, thanks for information my jeep 2005 wrangler doesn't not start or crank at all.

This is not a Select-A-Loc. As soon as I saw the clutch pack, I knew it was the Ected. And then you read it off the carrier. They are different.

I have a question for you about an issue on my 2014 Maxima. If I get on the gas, my steering wheel jerks left or right. I have to let go of the wheel and let it happen or it will crash the car. When I let off the gas same thing the steering wheel jerks one way or the other and if you don't let go it will throw you off the road. Its not an alignment or the tires. Have you ever seen a problem like that? Any ideas?

I'm thinking it's a steering problem. She should head straight back to the dealer and get rid of it.

Yeah, I had a broken plastic fitting and swapped it out for brass. Weird, I barely remember all that went in to rebuilding my '90 Fatboy fuel system but it worked out great and I could do it again. Keihin CV carbs properly made the compromise between carburetion and fuel injection.

REPORT ALL THESES FORD EDGE 2018 AND OTHER YEARS COOLANT EVENTUALLY GO INTO CYLINDERS ABD CRACK CYLINDERS!!! FORD MOTOR WILL NOT RECALL OR TAKE RESPONSIBILITY!!!!! TAKE BACK DON'T BUY FORD!!!! IF IT HASN'T HAPPENED IT WILL!!!🤢🤢🤮🤮

do I need to do the allignement of crancshaft if I need to change my transmission??Any body can answer??

If I have to change my transmission do I need to do the allgnement of crancshaft ??

Buyer beware. People do your research before buying a ford product. If it’s 1 mile over warranty ford will drop you. Remember it’s not a Toyota or Honda product. Ford engineering is terrible they simply can’t build a reliable 4 cylinder boosted engine.

Had the problem 2017 edge titanium. Ford would do nothing. Traded it at a loss for a Toyota. Ford will never get another cent from me. I will always encourage my friends to do the same !!

Clock spring issue?

Your insights and suggestions are incredibly valuable! We won't be able to test them until Monday, but your input today will pave the way for a swift resolution. Thank you for lending a hand in solving this issue!

My first suspicion is always that there's a ground fault somewhere. My second guess is something wrong with the power steering module and when it glitches it disrupts coms to everything else downstream on the bus. 🤔 Third guess is that the wiper stalk wiring has chafed and it's shorting in a way that disrupts coms or takes the wiper module/body module offline? Idk this is a weird issue for sure. I'm super curious wtf is causing that!!!

ok if i replace just the front two calipers, i should then bleed those 2 only right? the bleeding for all 4 was because he wanted a whole new set on all 4? would you bother to replace the rubber hose that connects to the brake hard line you removed in the beginning of video or if it doesnt appear worn out is it still good to go?

Will the motor make any noise? Or if no noise is it the relays?

Thanks for the video! Saved us on the side of the river after a week long river trip, you’re a life saver!

God bless you have a blessed day today 🙏